Rotary Meter Related TM/HT/SE/GE Series (Discontinued Products)
HT Series Handheld Tachometer
TM-2000 series tachometer (discontinued)
- I am using LG-916 and TM-2130 together, but the output voltage remains at zero. I am also using LG-930 and FV-1100 together, but the output voltage fluctuates in a wave-like manner.
- BCD Output and Positive/Negative Logic
- Example setup for the TM-2100 series tachometer - 3: "Attach one reflective sticker to the rotating axis, detect it with the LG-916, and display the rotational speed at ○○○○ r/min."
- Example of setting up the TM-2100 series tachometer - 1: "Detect 60 teeth on the gear with the MP-9100 and display the rotational speed at ○○○○ r/min."
- "Example setting for the TM-2100 series tachometer - 2: Detecting a gear with 60 teeth using the MP-981 and displaying the rotational speed at ○○○○ r/min."
- "Example of setting for TM-2100 series tachometer - 5: Connect to RP-704ZA-100P/R and display speed at ○○○.○ m/min"
- "Example of setting for TM-2100 series tachometer - 6: Connect to RP-721-120P/R and display speed at ○○○.○ m/min"
- How to set up the analog output of TM-2130
TM-3100 series tachometer
- How to set the diameter of the rotating body in units of 0.01 mm when measuring peripheral speed (L.SPEED) with the TM-3100?
- Please compare the measurement accuracy of TM-3100 and HT-5500.
- TM-3100 Common: "I want to return to the measurement screen all at once from the deep settings screen in the settings menu."
- "Example of Settings for TM-3100 Series Tachometer - 2: Setting Procedure for Rotational Measurement Using LG-916/930/9200 Rotational Detectors"
- Currently using LG-9200/TM-3130. Measuring a rotating object with a diameter of 60 mm that has 25 small reflective stickers attached. I would like to know the possible causes and solutions for the following issue: when the rotation detection is turned OFF, the display on the TM remains for a few seconds and then (after some time) goes to zero.
- TM-3100 Series Tachometer "Menu Settings Button Operations"
- "For the TM-3100, what happens to the analog output and comparator output when the MENU button and CONDITION button are pressed during measurement (while the rotation speed is being displayed)?"
- Example of setting for TM-3100 series tachometer - 4 "Setting procedure for rotation measurement using MP-9100 rotation detector"
- Example of Setting for TM-3100 Series Tachometer - 1: "Setting Procedure for Rotation Measurement Using MP-981 Rotation Detector"
- "Check the built-in functions (cards) of the TM-3100 series tachometer"
- How to set a value of less than 0.1 mm for pulse distance during velocity measurement with the TM-3100?
- Example of Setting for TM-3100 Series Tachometer - 3: Setting Procedure for Line Speed Measurement Using RP-7400-120P/R Roller Encoder
- What are the settings for replacing a TM-2100 with a TM-3100 when the pulse count of the combined sensor is unknown?
- What is the difference between Hz units and r/s units in TM-3100?
- The relationship between the display of TM-3100 and its analog/BCD output.
- Is the TM-3100 series compatible with the older TM-800/8000 series and TM-2100 series?
- The display of the TM-3100 is unstable (it counts incorrectly).
- How to reset to factory settings.
- How to set button operation to key lock state
- In the TM-3100, when the input amplifier configuration is set to PULL UP, what is the voltage of the power supply and what is the resistance value used for the PULL UP?
- What is the analog output (voltage, current signal) during the SS interval measurement mode?
- "When I want to turn the relay OFF (open) in case of abnormal conditions."
- "I want to output a comparison to see if the rotational speed is within a certain range."
- Can you tell the status of the comparator's judgment from the display on TM-3140?