Handy Diesel Engine Tachometer
GE-1400
Simply clamp the detector to the fuel injector. This Digital Tachometer is designed specifically for measuring the rotational speed of 4-stroke diesel engines. The CP-044 detector (sold separately) can be attached to one of the fuel injector pipes with a single touch, allowing for direct reading of engine rotational speed in r/min. It comes standard with both analog output (switchable with monitor output) and pulse output. The analog output can be used for recording with a data recorder, etc. (the monitor output can be used for checking sensor waveforms or as an input signal for analysis with an FFT analyzer), and the pulse output can be used as a signal for tracking analysis with an FFT analyzer.
Please note: The GE-1400 may not be able to measure certain engine types. For engines that have not been used before, please check with a demo unit. Please contact your nearest sales office to request a demo unit. *We apologize for the inconvenience, but please provide your own batteries.
| Adaptive engine | 4-stroke diesel engine |
| Detection method | Detects pulsations in the injection pipe that occur during fuel injection. |
| Compatible detectors | CP-044 (optional) |
| Arithmetic method | Periodic calculation method |
| Measurement time | Within 1 second + one cycle time of the input signal |
| Display section | LCD display, 5 digits, with backlight (character height: 10.2mm) |
| Display update time | 1 ± 0.2s |
| Unit of measurement | r/min、r/s |
| Measurement range | 400–8000 r/min (r/s is the range obtained by dividing the measured value in r/min by 60) |
| Measurement accuracy | Displayed value * × (±0.02%) ± 1 count (*The displayed value is the count value excluding the decimal point.) |
| Memory function | 20 data points (MAX) |
| Overrange function | An overrange (ERROR) mark is displayed when the measured value exceeds the display range. |
| Rotation limit warning function | When the rotation speed exceeds a preset upper limit, an upper limit warning (↑ mark) is displayed. |
| Trigger level adjustment function | Adjust using the rotary volume control on the right side of the unit. |
| Analog output | Output relative to the displayed rotation speed value Output voltage: 0 to 1 V / 0 to full scale (full scale is arbitrarily set) Conversion method: 10-bit D/A conversion method Linearity: ±1%/full scale Output update time: within 50 ms + 1 cycle time Temperature stability: ±0.05%/full scale/°C (span & zero) Setting error: ±0.5%/full scale Load resistance: 100 kΩ or more |
| Monitor output | Analog output for monitoring after waveform shaping of the sensor signal. (Use by switching between the above rotation speed analog output) Load resistance: 100 kΩ or more |
| Pulse output | Output one pulse for each signal detected. Output voltage: Hi +4.5V or higher, Lo +0.5V or lower Output logic: Positive logic Load resistance: 100 kΩ or more |
| Operating temperature range | 0 to +40℃ |
| Storage temperature range | −10℃ ～＋50℃ |
| Power supply | 4 x AAA batteries (1.5V) or dedicated AC adapter PB-7090 (optional) |
| battery life | 16 hours or more (with backlight off), 8 hours or more (with backlight on) |
| Battery warning display | A warning mark (LOW mark) will be displayed when the battery voltage drops below approximately 4.4 V. |
| Outline drawings |
180.5 (L) × 66 (W) × 47.5 (D) mm (main unit only)
|
| Weight | Approximately 280g (main unit only / batteries not included) |
| Accessories | Carrying case, AX-501 output cable, instruction manual x 1 |
| price | |
| Option |
|
*Please provide your own batteries.
| Target Engine | Diesel engine |
| Detection method | Piezoelectric element detects pulsation during fuel injection. |
| Measurable pipe diameter | Φ4 ～ 8 mm |
| element compressive strength | 1960 bar |
| Measurement range | 400～6000 r/min |
| Signal cable | Heat-resistant signal cable, 4.9 m (direct cable outlet) - (R03PB6M) |
| Operating temperature range | 0～＋80℃ |
| Outline drawings |
Φ 32 ×72 mm
|
| Weight | Approximately 120g |
| price |
