High-speed F/V converter
FV-1500
The FV-1500 high-speed F/V converter is a highly responsive frequency (F)/voltage (V) converter that converts frequency signals proportional to rotational speed and movement speed into voltage signals.
It supports motors used in hybrid and electric vehicles, as well as the acceleration of manufacturing lines in production factories, and can measure transient phenomena such as startup characteristics, minute rotational fluctuations during steady rotation, and flow rate changes with high response.
When the input signal rapidly decelerates due to a rotating body, and no input is received beyond the previous pulse interval, this function reduces and stops the rotational output (speed analog).
When Follow Function is ON:
If no signal input is received after waiting for 1.5 to 16 times the previous signal pulse interval, the analog output will become 0.
When Follow Function is OFF:
After the input signal becomes 0 (OFF), the analog output will become 0 after being held at the minimum measurement frequency (0.2 Hz).
| Input Specifications | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Input Connector | BNC (CO2 type), terminal block | ||||||||
| input format | Single-phase AC/DC no voltage (open collector compatible +12 V pull-up) switching 90° phase difference two-phase signal (DC input only) |
||||||||
| input voltage | AC input signal voltage range: 0.3 Vp-p to 30 Vp-p | ||||||||
| DC input signal voltage range: Lo; 1 V or less, Hi; 4 to 30 V | |||||||||
| filter |
OFF / 20 kHz / 120 kHz low-pass filter |
||||||||
| input impedance | 2.2 kΩ | ||||||||
| AC coupling frequency | 0.9 Hz approximately -3 dB | ||||||||
| Minimum input pulse width | 1.5 μs | ||||||||
| Input signal edge switching | Switch between ascending and descending | ||||||||
| Input Frequency Range | 0.2 Hz to 320 kHz
|
||||||||
| Signal output specifications | |||||||||
| analog output signal | |||||||||
| Analog output terminal |
BNC/C02 type (voltage output) or |
||||||||
| conversion time | Cycle within +3.5μs | ||||||||
| D/A resolution |
16 bit |
||||||||
| filter |
OFF / 3 Hz / 10 Hz / 1 kHz switching low-pass filter |
||||||||
| Analog output terminal signal |
|
||||||||
| Output DC offset | Voltage output: within ± 10 mV | ||||||||
| Current output: within ± 0.01 mA | |||||||||
| temperature coefficient | Voltage output: ± 0.02 %/F.S./℃ | ||||||||
| Current output: ± 0.07 %/F.S./℃ | |||||||||
| output impedance | Above 50 Ω (voltage output) | ||||||||
| Linearity (in full scale mode) |
|
||||||||
| pulse output signal | |||||||||
| Pulse output | BNC (CO2 type) Output terminal voltage: Lo: +1 V or less, Hi: +4.5 V or more Load resistance: 100 kΩ or more |
||||||||
| Pulse Output Option (FV-0154) |
Open collector output Voltage resistance: DC30 V, sink current: 50mA or less |
||||||||
| Comparator output signal (optional FV-0152) | |||||||||
| Comparator output terminal | Terminal block (Phoenix Contact MC1,5/6-STF-3,81) | ||||||||
| output format | Semiconductor relay (1 make contact) 2CH | ||||||||
| Maximum contact capacity | DC 30 V / 1 A | ||||||||
| Contact ON Resistance | 25 ohms or less | ||||||||
| setting | UPPER, LOWER Relay ON when UPPER set value ≦ measured value, Relay ON when LOWER set value ＞ measured value |
||||||||
| ancillary functions | Delay function | It is possible to set the contact ON or OFF from 0 to 100 times when the threshold is exceeded continuously beyond the set number of times. | |||||||
| hysteresis function | Change the return frequency or rotation speed, movement speed 0 to 20 % can be set in increments of 1 %. |
||||||||
| hold function | Change the minimum output time to maintain the contact ON state from 1 ms to 1000 ms Can be set in 1 ms increments |
||||||||
| Function | |||||||||
| moving average | OFF / Simple average 2 to 720 times / Indexed average 2 to 64 times | ||||||||
| number of pulses | 1 to 999999 P/R | ||||||||
| factor | 0.0001～99999 | ||||||||
| Incremental Doubling / Weekly Division | Multiplication: OFF / 2 / 4 (only when a 90° phase difference 2-bit signal input is present) Division: OFF, 2 to 1000 | ||||||||
| Condition Memory | Remember 10 conditions | ||||||||
| Rapid Deceleration Tracking (Predictive Calculation) | OFF / TYPE1 / TYPE2 | ||||||||
| Estimated stop time | OFF / NUM: 1.5x to 16x / TIME: 1 ms to 4000 ms | ||||||||
| Direction discrimination | OFF / ON (only when two signals with a 90° phase difference are input) | ||||||||
| CAL | Voltage output ZERO: 0 V, FULL: 10 V | ||||||||
| Current output ZERO: 0 mA (4 mA), FULL: 16 mA (20 mA) | |||||||||
| Display | |||||||||
| display accuracy | Display value * X (±0.01%) ± 1 count (Note: The display value indicates the count value excluding the decimal point) | ||||||||
| Display | Fluorescent display tube (display range 69.85 mm × 11.45 mm) with 4-level brightness switching. | ||||||||
| Display update time | 0.5s, 1s | ||||||||
| Display unit ※ | Hz, r/min, m/min, USER | ||||||||
| State LED display | SIG | Lights up every time a signal is input. | |||||||
| Measurement Mode | Full scale, deviation, automatic deviation tracking (option FV-0151) | ||||||||
| Power supply for sensors | |||||||||
| Power supply for sensors | +12 V ± 10% 150 mA, +5 V ± 10% 150 mA, selectable via the rear switch. | ||||||||
| Applicable Standards | |||||||||
| CE marking | Low Voltage Directive EN61010-1:2010 | ||||||||
| EMC Directive EN61326-1:2013 | |||||||||
| General Specifications | |||||||||
| Input and Output Ground | The signal grounds for the signal outputs (V OUT, I OUT) are common (connected to the chassis) The signal grounds for the signal inputs (SIG IN, SIG 1, SIG 2) and sensor power supplies (+12V, +5V) are common The grounds for the signal inputs and sensor power supplies are isolated from the chassis. The grounds between input and output are isolated The maximum withstand voltage between isolated signal grounds and between the chassis is 42 Vpk |
||||||||
| Power supply voltage range | Includes a dedicated AC adapter for DC 16 V (AC 100-240 V). | ||||||||
| power consumption | approximately 36 VA or less | ||||||||
| Operating Temperature Range | 0 to 40 °C | ||||||||
| Storage Temperature Range | -10 to 50 °C | ||||||||
| Operating Humidity Range | 5% to 80% (provided that there is no condensation) | ||||||||
| Storage Humidity Range | 5 to 85% (provided that there is no condensation) | ||||||||
| Outline Dimensions | 210(W) × 44(D) × 200(D) mm (excluding protrusions)
|
||||||||
| Weight | approximately 1 kg | ||||||||
| Accessories | Dedicated AC adapter (PS-P20023 / VM1391-VM1700 2M) ×1, Instruction manual ×1, connector (MC1.5/6-STF-3.81) ×1 |
||||||||
| Price/Options | |||||||||
| Price | |||||||||
| Option |
|
||||||||
