Skip to content

Select your region & language

Global

Region

Linear Gauge Sensor
Discontinued Products
GS-6630

GS-1713A/GS-1730A
GS-3813B/GS-3830B
GS-4730A/GS-4813A
GS-5050A
GS-5050A/GS-5100A
GS-6713A/GS-6730A

The GS series digital linear gauge sensors include the compact and low-cost basic GS-1700/1800 series, the vibration-resistant GS-6700/6800 series with 1.5 times the vibration and shock resistance of the basic type, the "tough gauge" GS-4700/4800 series which pursues the heavy-duty performance required in manufacturing sites, and the long-stroke type GS-5050/5100 series with a long measuring range (stroke) of 50mm and 100mm. All models employ a bearing-type bearing mechanism, which significantly improves bearing life.
The "Tough Gauge" GS-4700/4800 was developed with the aim of addressing the deterioration of the measurement environment that accompanies increased work efficiency in manufacturing sites, such as shortening cycle times and enabling simultaneous manufacturing and inspection.

● Three times the bearing life compared to conventional products
Measurement operation: 5 million times → 15 million times
● Enhanced dustproof, waterproof, and oilproof performance compared to conventional products.
Protection rating: IP64 → IP66G
● Twice the vibration and shock resistance compared to conventional products.
Vibration resistance 98 m/s2 →196 m/s2
Impact resistance 980 m/s2 →1960 m/s2

General-purpose type

General-purpose type

GS-1713A/GS-1730A
Resolution 10 µm
GS-1813A/GS-1830A
Resolution 1 µm

Basic type (general purpose, waterproof structure IP64)

  • This is the successor model to the GS-1500/1600 series.

  • By adopting bearing support, the spindle's sliding life has been extended compared to conventional products.

Specification

  GS-1713A GS-1730A GS-1813A GS-1830A
Measurement range 13 mm 30 mm 13 mm 30 mm
Resolution 10μm 1μm
Indication accuracy (at +20°C) 3 μm 3 μm 2 μm 3 μm
Maximum response speed *1 1(4) m/s 0.3(1.2) m/s
Measuring force (downward) *2 1.3 N or less 1.9 N or less 1.3 N or less 1.9 N or less
Measurement force adjustment range (optional) *3 0.7 ～ 2.2 N 1.0 ～ 3.1 N 0.7 ～ 2.2 N 1.0 ～ 3.1 N
Number of sliding cycles (according to our company's conditions) 6.5 million times
Protection level (excluding connector portion) IP64
Stem diameter ⌀15 mm+0-0.009
Power supply DC 4.5 ～ 5.5 V
Current consumption (when supplied with DC 5 V) 120 mA or less
Signal output (when supplied with DC 5 V) Two-phase square wave signal, phase difference 90°±20°, output voltage Hi: 4.5 V or higher, Lo: 0.4 V or lower.
Output Impedance Approximately 22 Ω
Vibration resistance (when not energized) *4 98 m/ s², 3 axes, each direction (75 minutes each), 10 Hz to 150 Hz sweep, 10 cycles.
Shock resistant (when not powered on) *4 980 m/s 2 3 axes in each direction ±X, Y, Z 3 times each Half sine wave Action time 6 ms
Operating temperature range 0 ～40 ℃
Storage temperature range -10 ～55 ℃
Cable length *5 Approximately 1.9 m
Mass (including cables and connectors) 約250 g 約310 g 約250 g 約310 g
Outline drawings Outline drawings
Accessories Instruction manual, wrench
price        

*1 When using our gauge counter, the values in parentheses are for use with DG-4140/DG-4160/DG-4190/DG-5100/DG-3000.
*2 The spindle may not fully retract when used in an upward position.
*3 Value when used downwards. If the measuring force is changed, the spindle may not return completely when used sideways or upwards.
*4 Vibration and shock resistance during measurement are not guaranteed to be the stated values.
*5 If the signal cable is cut or modified midway, it will not comply with CE marking.

Vibration-resistant and shock-resistant type

Vibration-resistant and shock-resistant type

GS-6713A/GS-6730A
Resolution 10 µm
GS-6813A/GS-6830A
Resolution 1 µm

Vibration-resistant type (vibration-resistant and waterproof structure IP64)

  • Vibration resistance is improved by using adhesive to secure electrical components.

  • By adopting bearing support, the spindle's sliding life has been extended compared to conventional products.

Specification

　 GS-6713A GS-6730A GS-6813A GS-6830A
Measurement range 13 mm 30 mm 13 mm 30 mm
Resolution 10 μm 1 μm
Indication accuracy (at +20°C) 3 μm 3 μm 2 μm 3 μm
Maximum response speed *1 1(4) m/s 0.3(1.2) m/s
Measuring force (downward) *2 1.3 N or less 1.9 N or less 1.3 N or less 1.9 N or less
Measurement force adjustment range (optional) *3 0.7 ～ 2.2 N 1.0 ～ 3.1 N 0.7 ～ 2.2 N 1.0 ～ 3.1 N
Number of sliding cycles (according to our company's conditions) 6.5 million times
Protection level (excluding connector portion) IP64
Stem diameter ⌀15 mm+0-0.009
Power supply DC 4.5 V～DC 5.5 V
Current consumption (when supplied with DC 5 V) 120 mA or less
Signal output (when supplied with DC 5 V) Two-phase square wave signal, phase difference 90°±20°, output voltage Hi: 4.5 V or higher, Lo: 0.4 V or lower.
Output Impedance Approximately 22 Ω
Vibration resistance (when not energized) *4 147 m/ s², 3 axes, each direction (75 minutes each), 10 Hz to 150 Hz sweep, 10 cycles.
Shock resistant (when not powered on) *4 1470 m/s 2 3 axes in each direction ±X, Y, Z 3 times each Half sine wave Action time 6 ms
Operating temperature range 0 ～ 40 ℃
Storage temperature range -10 ～ 55 ℃
Cable length *5 Approximately 1.9 m
Mass (including cables and connectors) 約250 g 約310 g 約250 g 約310 g
Outline drawings Outline drawings
Accessories Instruction manual, wrench
price        

*1 When using our gauge counter, the values in parentheses are for use with DG-4140/DG-4160/DG-4190/DG-5100/DG-3000.
*2 The spindle may not fully retract when used in an upward position.
*3 Value when used downwards. If the measuring force is changed, the spindle may not return completely when used sideways or upwards.
*4 Vibration and shock resistance during measurement are not guaranteed to be the stated values.
*5 If the signal cable is cut or modified midway, it will not comply with CE marking.

Vibration-resistant, oil-resistant, and long-life type

Vibration-resistant, oil-resistant, and long-life type

GS-4713A/GS-4730A
Resolution 10 µm
GS-4813A/GS-4830A
Resolution 1 µm

Long-life type (vibration-resistant and oil-resistant structure IP66G)

  • The adoption of ball spline bearings significantly increased bearing strength, resulting in three times the number of sliding cycles compared to conventional designs.

  • The protection structure achieves IP66G.

  • Its vibration and shock resistance are twice that of the basic model. This allows for faster cycle times and greater flexibility in adapting to on-site work environments.

Specification

  GS-4713A GS-4730A GS-4813A GS-4830A
Measurement range 13 mm 30 mm 13 mm 30 mm
Resolution 10 μm 1 μm
Indication accuracy (at +20°C) 3 μm 3 μm 2 μm 3 μm
Maximum response speed *1 1(4) m/s 0.3(1.2) m/s
Measuring force (downward) *2 1.8 N or less 2.4 N or less 1.8 N or less 2.4 N or less
Measurement force adjustment range (optional) *3 0.8 ～ 2.5 N 1.5 ～ 3.9 N 0.8 ～ 2.5 N 1.5 ～ 3.9 N
Number of sliding cycles (according to our company's conditions) 15 million times
Protection level (excluding connector portion) IP66G
Stem diameter ⌀15 mm+0-0.009
Power supply DC 4.5 ～ 5.5 V
Current consumption (when supplied with DC 5 V) 120 mA or less
Signal output (when supplied with DC 5 V) Two-phase square wave signal, phase difference 90°±20°, output voltage Hi: 4.5 V or higher, Lo: 0.4 V or lower.
Output Impedance Approximately 22 Ω
Vibration resistance (when not energized) *4 196 m/ s², 3 axes, each direction (75 minutes each), 10 Hz to 150 Hz sweep, 10 cycles.
Shock resistant (when not powered on) *4 1960 m/s 2 3 axes in each direction ±X, Y, Z 3 times each Half sine wave Action time 6 ms
Operating temperature range 0 ～ 40 ℃
Storage temperature range -10 ～ 55 ℃
Cable length *5 Approximately 4.9 m
Mass (including cables and connectors) Approx. 325g Approx. 385g Approx. 325g Approx. 385g
Outline drawings Outline drawings
Accessories Instruction manual, wrench
price        

*1 When using our gauge counter, the values in parentheses are for use with DG-4140/DG-4160/DG-4190/DG-5100/DG-3000.
*2 The spindle may not fully retract when used in an upward position.
*3 This is the range of modifications made when modifying the device to enable upward use. (The values represent the measurement force when the device is facing downwards.)
*4 Vibration and shock resistance during measurement are not guaranteed to be the stated values.
*5 If the signal cable is cut or modified midway, it will not comply with CE marking.
(Note) Dustproof rubber is subject to a fee for pickup and replacement.

Long stroke type

Long stroke type

GS-5050A/GS-5100A
Resolution 10 µm
GS-5051A/GS-5101A
Resolution 1 µm

Long stroke type

  • Bearings are used for the shaft support.

  • We have expanded our product lineup by adding a new model with a 100 mm stroke and 1 μm resolution.

  • The mounting hole pitch and the distance to the spindle tip when mounted are the same as those of the GS-5011.

Specification

  GS-5050A GS-5100A GS-5051A GS-5101A
Measurement range 50 mm 100 mm 50 mm 100 mm
Resolution 10 μm 1 μm
Indication accuracy (at +20°C) 10 μm 12 μm 4 μm 5 μm
Maximum response speed *1 1(4) m/s 0.3(1.2) m/s
Measuring force (downward) *2 2.9 N or less 5.2 N or less 2.9 N or less 5.2 N or less
Measurement force adjustment range (optional): downward *2 1.8 ～ 6.2 N 3.1 ～ 7.2 N 1.8 ～ 6.2 N 3.1 ～ 7.2 N
Measurement force adjustment range (optional): Upward *3 1.8 ～ 6.2 N 3.1 ～ 7.2 N 1.8 ～ 6.2 N 3.1 ～ 7.2 N
Number of sliding cycles (according to our company's conditions) 15 million times
Protection level (excluding connector portion) IP5X
Stem diameter ⌀15 mm+0-0.009
Power supply DC 4.5 ～ 5.5 V
Current consumption (when supplied with DC 5 V) 120 mA or less
Signal output (when supplied with DC 5 V) Two-phase square wave signal, phase difference 90°±20°, output voltage Hi: 4.5 V or higher, Lo: 0.4 V or lower.
Output Impedance Approximately 22 Ω
Vibration resistance (when not energized) *4 147 m/ s², 3 axes, each direction (75 minutes each), 10 Hz to 150 Hz sweep, 10 cycles.
Shock resistant (when not powered on) *4 1470 m/s 2 3 axes in each direction ±X, Y, Z 3 times each Half sine wave Action time 6 ms
Operating temperature range 0 ～ 40 ℃
Storage temperature range -10 ～ 55 ℃
Cable length *5 Approximately 4.9 m
Mass (including cables and connectors) 約570 g 約655 g 約570 g 約655 g
Outline drawings Outline drawings
Accessories Instruction manual, wrench
price        

*1 When using our gauge counter, the values in parentheses are for use with DG-4140/DG-4160/DG-4190/DG-5100/DG-3000.
*2 The spindle may not fully retract when used in an upward position.
*3 This is the range of modifications made when modifying the device to enable upward use. (The values represent the measurement force when the device is facing downwards.)
*4 Vibration and shock resistance during measurement are not guaranteed to be the stated values.
*5 If the signal cable is cut or modified midway, it will not comply with CE marking.

High-resolution type

High-resolution type

GS-3813B/GS-3830B
Resolution 0.1 µm
DG-5100 Digital Gauge Counter
(GS-3800 series compatible counter)

DG-5100 Digital Gauge Counter

  • Compared to conventional products, it enables more precise measurements (10 times higher resolution: 1 μm → 0.1 μm).

  • Three times the bearing life compared to conventional products (5 million measurement cycles → 15 million cycles)

  • Enhanced dust, water, and oil resistance compared to conventional products (protection rating IP64 → IP66G)

  • Twice the vibration and shock resistance compared to conventional products (Vibration resistance 98 m/ s², shock resistance 980 m/ s² → Vibration resistance 196 m/ s², shock resistance 1960 m/ s²)

  • By adopting ball spline bearings and developing a new optical system, it has become possible to achieve both high resolution and environmental resistance.

  • Since the detection signal can be extracted with a square wave output (line driver output), it can be connected directly to a PLC.

Specification

　 GS-3813B GS-3830B
Measurement range 13 mm 30 mm
Adaptive Gauge Counter DG-5100
Resolution 0.1 µm
Indication accuracy (at 20°C) 1 µm
Maximum response speed *1 300 mm/s (1.2 m/s)
Measuring force (downward) *2 2.3 N or less 2.7 N or less
Measurement force adjustment range (optional) *2 0.8 ～ 3.0 N 1.5 ～ 2.5 N
Measurement force adjustment range (optional) *3 0.8 ～ 3.0 N (Not allowed)
Number of sliding cycles (according to our company's conditions) 15 million times
Protection level (excluding connector portion) IP66G
Stem diameter ⌀15 mm+0 -0.009
Power supply DC 4.5 ～ 5.5 V
Current consumption (when supplied with DC 5V) 150 mA or less
Signal output (when supplied with DC 5V) 90° phase difference differential square wave, RS422A compliant, line driver output (equivalent to 26C31).
Vibration resistance (when not energized) *4 196 m/ s², 3 axes, each direction (75 minutes each), 10 Hz to 150 Hz sweep, 10 cycles.
Shockproof (when not powered on) *4 1960 m/s 2 3 axes in each direction ±X, Y, Z 3 times each Half sine wave Action time 6 ms
Operating temperature range 0 ～ 40 ℃
Storage temperature range -10 ～ 55 ℃
Cable length Approximately 5 m
Mass (including cables and connectors) Approximately 350g Approx. 420g
Outline drawings Outline drawings
Accessories Instruction manual, wrench
price    
Option

(List of Cables and Accessories)		 AA-969 Finger Lift
• ST-0230, ST-044B (usable only with GS-3830) Gauge Stand
AA-4104 (13 mm) / 4105 (30 mm) Replacement dustproof rubber
AA-844 (30 mm) / 845 (50 mm) Extension Spindle
• Various measuring probes
AA-3310 Mounting Bracket
AA-8901 (5 m) / AA-8902 (10 m) / AA-8903 (20 m) / AA-8904 (30 m) Extension Cables

*1 When using our gauge counter, the values in parentheses are the electrical response speeds when using the DG-5100.
*2 The spindle may not fully retract when used horizontally (below 10°C) or vertically.
*3 This is the range of modifications made when modifying the device to enable upward use. (The values represent the measurement force when the device is facing downwards.)
*4 Vibration and shock resistance during measurement are not guaranteed to be the stated values.
*5 If the signal cable is cut or modified midway, it will not comply with CE marking.
(Note) Dustproof rubber is subject to a fee for pickup and replacement.

Inquire about this product

Download

Outline Drawings

Instruction Manual

最終更新日:2025/09/03